Lotus Europa Community

Power was out most of the day here so I looked for something to do manually.
I have ten Cosmic wheels to refinish, six Lotus and four for TR4.
Working on just one today I am reminded how labor intensive this could be.
I used aluminum duct tape to mask off the bare aluminum areas.
I plan to soda-blast the black to bare aluminum without affecting the bright areas then buff with scratch pads.
A bit more tedious than expected but I hope the masking will hold up well enough to leave it in place for repainting.
Just doing one for now as an experiment.
Not a horrible job and I am certain I would not want to pay someone else for their time to do it either.
If this works well it should be possible to PP silver then mask for black/dark grey.
I found a shop to redo the original diamond-cut for them but the cost is the same as just buying the new reproductions!
Thinking that PP should be less cost and very durable, particularly if I do the masking.
I think PP can be masked with normal paper tape.
PP is not original of course but my plan is to DRIVE this car.
Anyone else done PP on their Cosmic's?

The otter switch has been redundant on my car since, well, probably before I got it in the 80s. The original owner of my car had fitted a dash switch and when I used the car daily in traffic I'd just flick it on if I got caught in a jam, otherwise it wasn't needed.  All that's happened in my ownership is to rewire and fit a relay in the circuit, plus of course changing the fan for a more modern unit. When I tidied up the radiator 10+yrs ago the old switch was still there but all it's doing is keeping the coolant in.

If you really do want automatic control and can't fit the OEM switch then aftermarket fans such as the Kenlow I have on the Elan came with a bulb sensor & leads which you could slide into the top hose. There is a small rubber moulding, hard to describe but mine is a sort of half circle with indentations for the wire. This sits on the alloy thermosat housing outlet and the original hose slides over the combination and seals very well. You can set the temperature you want it to come on and it also has an override switch with a light to tell you when it's on. The original fan has long since been replaced by a slimmer, modern unit but the controller is still in there.

Brian

  Got to clean up the lines in the graphics. I did it freehand and will nib sand till I get it perfect, then reclear the entire panel. I love making people bring out the magnifying glasses 😂
  I doubt this will be attached to my car but I’ll try my best to keep the JPS theme alive.
Dakazman

.

Been derailed by some serious dentistry, having been given strict instructions about limiting physical effort I've left the doors until I've healed a bit. Instead of which, I managed to get the dash out, and can look at it in all its (ahem) glory. Crash pad looks ok, but might get a covering of vinyl to freshen it up. Fascia panel has me in two minds, I'm not a fan of the OE lacquered floorboard look, and although the walnut veneer looks ok, i might try stripping the panel back and painting it matt / satin black.

So, onto stupid question time. My radiator was crumbling to bits as I removed it, but as luck would have it there was a Europa rad on eBay which looked decent, even had a Spal fan fitted (mine looked like it had been submerged with the Titanic). It arrived today, and is in evidently good nick, but doesn't have a hole for the Otter switch - it has an indented circle where it would be fitted but no hole. So I was wondering if everyone on here had an otter switch, or is there an alternative to switch on your fan when the radiator gets... otter?  And yes, I am getting ahead of myself buying parts at the strip down stage, but it was retail therapy.

Yea, the axles seemed fine. The play is definitely from the hole. I do not know why I never checked before. Like you said it is a tight fit (even now), until everything is apart and you put only the bolt back in without the shock and link. Then the bolt wobbles. Its worn like an inverted cigar. The center is tight, but the ends are enlarged.
I was thinking of an aluminum bushing too. I can make my own and get a perfect fit. The other reason I asked is that I read (I think in Dave Bean's catalog that you cannot bush the bearing housing for a bearing - it has been tried and cracks.